Use and Fence Basics

Irish Plugs are 230V. Frequency is 50 Hz. Fencers generally operate at 220V and put out a high pulse voltage of between 2000 and 10,000 V but typically 6000-8000 is a good fence. But very low amperage or current (around 120 miliamps) i.e. High voltage and low amperage. From time to time, you will encounter voltage drops or face grounding issues along your fence line. When this happens, having a fence tester, also known as a voltage meter or voltage tester, is needed to identify your fence problem. when a fence is setup it isn't ‘turned on and set to e.g. 8kv or 6kv’. It simply puts out the same power at all times. What drains it is the size of the fence or the fact that there is a hedge brushing off of it or an animal tried to jump it and pulled part of the fence down and it is hitting the ground somewhere. Basically, an electric fence puts out a steady current. if something is touching the fence then it causes it to drain and lowers the voltage.

Depending on the quality of your multimeter you'll see a fluctuating of numbers on the screen, which tells you that you're getting some kind of pulse, but you have no idea if it's the full potential or not. Also, if the multimeter is of lesser quality, you'll either blow the fuse inside, or ruin the circuit board inside. Unfortunately, you can't use a regular volt meter for testing electric fence chargers, they're just not designed for the high voltage (8Kv) pulse that Boundary Blade has been designed for.

No. You hold the closed unit IN FRONT of the fence link shown on the packaging. The product is a Low cost 5-light wireless tester to measure the approximate fence voltage without a Ground Spike.

2500 V – 4000 V – 6000 V – 8000 V

No grounding spike is required.

Yes, the lights are strong LEDs and can be seen in sunshine.

Make sure the blade is fully closed. The fence tester will NOT WORK if the blade is open. With the blade closed, simply hold the unit IN FRONT of the electrified fence, close to the current, and push the ‘PRESS’ button.

Warranty

The unit comes with a 30 day warranty. Any opening of areas except for battery compartment voids all warranty. Please Ensure your unit is cleaned properly, used sensibly, and kept dry as this will be inspected if returned. Please email sales@boundaryblade.com if you need to open a support ticket.

Materials

The blade material is stainless steel 30Cr13. This steel has good mechanical processing performance. After heat treatment (quenching and tempering), it has excellent corrosion resistance and high polishing strength and wear resistance. The blade is flame retardant.
The length of the blade is 7.24cm (2.85 inches)

The product casing material is TPU (thermoplastic polyurethane). TPU not only possesses excellent properties of high tension, high tensile strength, strong toughness and aging resistance, but also is a mature environmental protection material. TPU has many applications including automotive instrument panels, caster wheels, power tools, sporting goods, medical devices, drive belts, footwear, inflatable rafts, and a variety of extruded film, sheet and profile applications.

No. It is advised to keep your Boundary Blade Clean, dry and away from water.

No. All Products come with 2 universal and replaceable CR2032 3v batteries. The batteries are not activated in any way unless the blade is closed AND the "PRESS" button is engaged.

If the ‘battery’ indicator light is on when testing, or you are not getting a reading, simply unscrew the reverse side and change the batteries. Please DO NOT remove the glue seals or anything from the front facing side of the tester as this will void all warranty.

The LED lights only need 3 to 9v. Batteries help protect the circuit board design in the event of a failure for safety.

No. There are no moving parts inside the product.

Dimensions and Weight

Full length of unit with blade opened: 18.33 cm
Length of unit with blade closed: 11.09 cm
Width of Unit: 3.88 cm
Depth of Unit: 2.07 cm

Package Dimensions: 22cm Length, 8cm width, 2.5cm depth

Blade Length Extended: 7.24 cm (2.85 Inches)

The weight of a single product is approx 90 grams

Product is powered by 2 x CR2032 3V Lithium Coin Batteries:
20mm is the diameter of CR2032 and 3.2mm is the thickness
Lithium Coin Cell
Nominal Voltage: 3.0 Volts
Maximum Current: 0.19A
Non - Rechargeable Disposal battery
Typical Capacity: 240 mAh @ 20°C 15kΩ Load
Service Life: ~720 Hrs @20°C 15kΩ Load
Typical Weight: 3.0 grams (0.10 oz.)
Operating Temp: -30C to 60C
Self-Discharge: ~1% / year

Safety

No. When testing the voltage of a live fence, the blade should not be opened from the sleeve or touched of a fence. The fence tester electronics will only get engaged to give you a reading when the blade is fully closed and the "PRESS" button engaged.

Yes but the correct way to test the fence is to hold the closed unit IN FRONT of the fence as shown on the packaging. An Electric fence emits a pulse. The insulating plastic of the handle does not conduct electricity, and the inner antenna is coated with an insulation layer. Always exercise caution and common sense.

Boundary Blade is a simple, cost effective spring self-locking pocket knife tool. It requires manual force to lock the blade in place, not gravity.
Folding blades that are part of a multi-tool device, and are under 3 inches are not classified as weapons.
Please always know and be aware of your local laws around the possession of knives.

Intellectual Property

All intellectual property, design, CAD and detailed production designs remains the property of Boundary Blade Ltd, and is not for distribution, resale, re-use, or communication elsewhere without our permission. Our unique IP protects a double-sided printed circuit board, with components especially designed and developed to fit inside an ultra-small space. All of them are patch low-power components and use small size button batteries compared to other tools which utilize a single sided PCB designs and 9v batteries. Boundary Blade is protected by Patents, Trademarks and Copyright under the Berne Convention globallly.

Certifications

Yes. RoHS, also known as Directive 2002/95/EC, originated in the European Union and restricts the use of specific hazardous materials found in electrical and electronic products (known as EEE). All applicable products in the EU market after July 1, 2006 must pass RoHS compliance.